home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Ham Radio 2000
/
Ham Radio 2000.iso
/
ham2000
/
mods
/
cellular
/
motorola.txt
< prev
next >
Wrap
Text File
|
1993-05-14
|
16KB
|
403 lines
MOTOROLA
NOTES: Some units have dual NAM's.
The ESN prefix is 130 decimal, 82 hex.
Motorola: 1-800-331-6456
There are MANY different models of Motorola phones sold under various
brand names, if you think it's a Motorola, it probably is.
Determine which access sequence to use:
HAND HELD PORTABLE MODELS
If the phone has a FCN button and no MENU button use sequence 1.
If the phone has no FCN button use sequence 2.
If the phone has a MENU button and a FCN button use sequence 4.
INSTALLED MOBILE PHONES AND TRANSPORTABLE MODELS
If the phone has no FCN button and no RCL button use sequence 3.
If the phone has a FCN button use sequence 4.
If the phone has a MEM button use sequence 5.
If the phone has a RCL button and no FCN button use sequence 6.
SEQUENCE# ACCESS CODE
1 FCN (SECURITY CODE TWICE) RCL
2 STO # (SECURITY CODE TWICE) RCL
3 CTL 0 (SECURITY CODE TWICE) *
4 FCN 0 (SECURITY CODE TWICE) RCL
5 FCN 0 (SECURITY CODE TWICE) MEM
6 CTL 0 (SECURITY CODE TWICE) RCL
The default security code is 000000. The CTL (control) button is the
single black button on the side of the handset.
NAM programing:
1. Turn the power on.
2. Within ten seconds enter the access sequence as determined above.
3. The phone should now show "01" in the left of the display, this is the
first programing entry step number. If it does not the security code
is incorrect, or the programing lock-out counter has been exceeded. In
either case you can still program the unit by following the steps under
TEST MODE PROGRAMING below.
4. The * key is used to increment each step:
Each time you press * the display will increment from the step number,
displayed on the left, to the data stored in that step, displayed on
the right. When the data is displayed make any necessary changes and
press * to increment to the next step number.
5. The SND key is used to complete and exit programing when any STEP
NUMBER is displayed.
If you have enabled the second phone number bit in step 10 below then
pressing SND will switch to NAM 2. Steps 01 thru 06, 09 and 10 will
repeat for NAM 2, the step number will be followed by a "2" to indicate
NAM two.
5. The CLR key will revert the display to the previously stored data.
6. The # key will abort programing at any time.
PROGRAMING DATA:
STEP# #OF DIGITS/RANGE DESCRIPTION
01 00000 - 32767 SYSTEM ID
02 3 DIGITS AREA CODE
03 7 DIGITS TEL NUMBER
04 2 DIGITS STATION CLASS MARK
05 2 DIGITS ACCESS OVERLOAD CLASS
06 2 DIGITS GROUP ID (10 IN USA)
07 6 DIGITS SECURITY CODE
08 3 DIGITS LOCK CODE
09 0333 OR 0334 INITIAL PAGING CHANNEL
10 6 DIGIT BINARY OPTION PROGRAMING (SEE NOTE 1)
11 3 DIGIT BINARY OPTION PROGRAMING (SEE NOTE 2)
NOTES:
Take care with Motorola's use of "0" and "1". Some options use "0" to
enable, some use "1".
1. This is a 6 digit binary field used to select the following options:
Digit 1: Internal handset speaker, 0 to enable.
Digit 2: Local Use Mark, 0 or 1.
Digit 3: MIN Mark, 0 or 1.
Digit 4: Auto Recall, always set to 1 (enabled).
Digit 5: Second phone number (not all phones), 1 to enable.
Digit 6: Diversity (Two antennas, not all phones), 1 to enable.
2. This is a 3 digit binary field used to select the following options:
Digit 1: Continuous DTMF, 1 to enable.
Digit 2: Transportable Ringer/Speaker, 0=Transducer, 1=Handset.
Digit 3: 8 hour time out in transportable mode, 0 to enable.
TEST MODE ACCESS:
INSTALLED MOBILE PHONES AND TRANSPORTABLE MODELS
To enter test mode on units with software version 85 and higher you must
short pins 20 and 21 of the transceiver data connector. An RS232 break out
box is useful for this, or construct a test mode adaptor from standard
Radio Shack parts.
For MINI TR or Silver Mini Tac transceivers (smaller data connector) you
can either short pins 9 and 14 or simply use a paper clip to short the
hands free microphone connector.
HAND HELD PORTABLE MODELS:
There are two basic types of Motorola portable phones, the Micro-Tac series
"Flip" phones, and the larger 8000 and Ultra Classic phones. Certain newer
Motorola and Pioneer badged Micro-Tac phones do not have a "flip", but
follow the same procedure as the Micro-Tac.
8000 & ULTRA CLASSIC SERIES:
If you have an 8000 series phone determine the "type" before trying to
enter test mode. On the back of the phone, or on the bottom in certain
older models, locate the F09... number this is the series number. If the
FOURTH digit of this number is a "D" you CAN NOT program the unit through
test mode, a Motorola RTL4154/RTL4153 programer is required to make any
changes to this unit.
Having determined that you do not have a "D" series phone the following
procedure is used to access test mode:
Remove the battery from the phone and locate the 12 contacts at the top
near the antenna connector. These contacts are numbered 1 through 12 from
top left through bottom right. Pin 6, top right, is the Manual Test Mode
Pin. You must ground this pin while powering up the phone. Pin 7 (lower
left) or the antenna connector should be used for ground. Follow one of
these procedures to gain access to pin 6:
1. The top section of the battery that covers the contacts contains
nothing but air. By careful measuring you can drill a small hole in the
battery to gain access to pin 6, alternately simply cut the top off the
battery with a hack saw. Having gained access use a paper clip to short
pin six to the antenna connector ground while powering up the phone.
2. If you do not want to "destroy" a battery you can apply an external 7.5
volts to the + and - connectors at the bottom of the phone, ground pin 6
while powering up the phone as above.
3. You can also try soldering or jamming a small jumper between pins 6 and
7 (top right to lower left), or between pin 6 and the antenna connector
housing ground. Carefully replace the battery and power up the phone. Use
caution with this method not to short out any other pin.
4. A cigarette lighter adaptor, if you have one, also makes a great test
mode adaptor as it can be disassembled to give you easier access to pin 6.
Many are pre marked, or even have holes in the right location. This is
because they are often stamped from the same mold that the manufacturer
uses for making hands free adaptor kits and these kits require access to
the phone's connectors.
MICRO-TAC "FLIP" SERIES:
This phone follows similar methods as outlined for the 8000 series above.
Remove the battery and locate the three contacts at the bottom of the
phone, the two outer contacts are raised and connect with the battery. The
center contact is recessed, this is the Manual Test Mode connector.
Now look at the battery contacts, the two outer ones supply power to the
phone, the center contact is an "extra" ground. This ground needs to be
shorted to the test mode connector on the phone. The easiest way to do
this is to put a small piece of solder wick, wire, aluminum foil or any
other conductive material into the recess on the phone. Having done this
carefully replace the battery and turn on the power, if you have been
successful the phone will wake up in test mode.
TEST MODE PROGRAMING:
Assuming you have completed one of the above steps correctly the phone
will wake up in test mode when you turn the power on. When you first
access test mode the phone's display will alternate between various status
information that includes the received signal strength and channel number.
The phone will operate normally in this mode. You can now access Service
Mode by pressing the # key, the display will clear and a ' will appear.
Use the following procedure to program the phone:
1. Enter 55# to access programing mode.
2. The * key advances to the next step. (NOTE that test mode programing
does NOT have step numbers, each time you press the * key the phone will
display the next data entry).
3. The CLR key will revert the display to the previously stored data.
4. The # key aborts programing at any time.
5. To complete programing you must scroll through ALL entries until a '
appears in the display.
6. Note that some entries contain more digits than can be displayed by the
phone, in this case only the last part of the data can be seen.
TEST MODE PROGRAMING DATA:
STEP# #OF DIGITS/RANGE DESCRIPTION
01 00000 - 32767 SYSTEM ID
02 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 1 BELOW
03 10 DIGITS MIN (AREA CODE & TEL#)
04 2 DIGITS STATION CLASS MARK
05 2 DIGITS ACCESS OVERLOAD CLASS
06 2 DIGITS GROUP ID (10 IN USA)
07 6 DIGITS SECURITY CODE
08 3 DIGITS LOCK CODE
09 3 DIGITS SERVICE LEVEL (LEAVE AT 004)
10 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 2 BELOW
11 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 3 BELOW
12 0333 OR 0334 INITIAL PAGING CHANNEL
13 0333 "A" SYSTEM IPCH
14 0334 "B" SYSTEM IPCH
15 3 DIGIT NUMBER PAGING CHANNEL (021 IN USA)
16 8 DIGIT BINARY OPTION PROGRAMING, SEE NOTE 4 BELOW
Steps 01 through 06 and 12 will repeat for NAM 2 if the second phone number
bit has been enabled in step 11.
NOTES:
Take care with Motorola's use of "0" and "1". Some options use "0" to
enable, some use "1".
These are eight digit binary fields used to select the following options:
1. (step 02 above, suggested entry is: 11101001 for "A" system, 10101001
for "B" sys)
Digit 1: Local use mark, 0 or 1.
Digit 2: Preferred system, 0 or 1.
Digit 3: End to end (DTMF) dialing, 1 to enable.
Digit 4: Not used, enter 0.
Digit 5: Repertory (speed) dialing, 1 to enable.
Digit 6: Auxiliary (horn) alert, 1 to enable.
Digit 7: Hands free (VSP) auto mute, 1 to enable (mutes outgoing hands
free audio until the MUTE key is pressed).
Digit 8: Min mark, 0 or 1.
2. (step 10 above, suggested entry is: 00000100)
Digits 1 - 4: Not used in USA, enter 0.
Digit 5: Single system scan, 1 to enable (scan A or B system only,
determined by bit 2 of step 02. Set to "0" to allow user the
option).
Digit 6: Super speed dial, 1 to enable (pressing N, or NN SND will dial
the number stored in memory location NN).
Digit 7: User selectable service level, 0 to enable (allows user to set
long distance/memory access dialing restrictions).
Digit 8: Lock function, 0 to enable (allows user to lock/un-lock the
phone, if this is set to 1 the phone can not be locked).
3. (step 11 above, suggested entry is: 00000000)
Digit 1: Handset programing, 0 to enable (allows access to programing
mode without having to enter test mode).
Digit 2: Second phone number (not all phones), 1 to enable.
Digit 3: Call timer access, 0 to enable.
Digit 4: Auto system busy redial, 0 to enable.
Digit 5: Speaker disable, 1 to enable (use with select VSP units only,
do not use with 2000 series mobiles).
Digit 6: IMTS/Cellular, 1 to enable (rarely used).
Digit 7: User selectable system registration, 0 to enable.
Digit 8: Dual antennae (diversity), 1 to enable.
4. (step 16 above, suggested entry is: 0011010 for portable and 0011011
for mobile units)
Digit 1: Not used, 0 only.
Digit 2: Not used, 0 only
Digit 3: Continuous DTMF, 1 to enable (software version 8735 and later)
Digit 4: 8 hour time-out, 0 to enable (software version 8735 and later)
Digit 5: Not used, 0 only.
Digit 6: Failed page indicator, 0 to enable (phone beeps when an
incoming call is detected but signal conditions prevent
completion of the call).
Digit 7: Portable scan, 0 for portable, 1 for mobile units.
OTHER USEFUL TEST MODE COMMANDS:
01# RESTART (POWER OFF THEN ON)
02# STATUS DISPLAY, ALTERNATES BETWEEN:
ABC DEF where:
ABC = Channel number
DEF = Received sensitivity for that channel
and: A B C D E F G where:
A = SAT frequency (0=5970, 1=6000, 2=6030, 3=no channel lock)
B = Carrier (0=off, 1=on)
C = Signalling tone (0=off, 1=on)
D = Power level (0 through 7)
E = Channel mode (0=voice channel, 1=control channel)
F = Receive audio mute (0=unmuted, 1=muted)
G = Transmit audio mute (0=unmuted, 1=muted)
Press * to hold display and # to end.
08# Unmute receive audio.
36NNN# (NNN in milliseconds) tunes from channel 1 to 666 in order, pauses
for NNN milliseconds, or press * to pause scan. # aborts.
07# Mute receive audio.
32# Initialize non-volatile memory (resets air timers and all memory
locations, makes phone look "new")
Other test mode commands are available, but not covered here. Use caution
as it is possible to alter settings that will make the phone operate
unreliably, if at all!
C-SCAN OPTION:
Newer Motorola phones are equipped with a feature called C-Scan, this is an
option along with the standard A/B system selections. C-Scan allows the
phone to be programed with up to five inhibited system ID's per NAM. This
is designed to prevent the phone from roaming onto specified non-home
systems and therefore reduce "accidental" roaming fees.
1. C-Scan can only be programed from test mode, power phone up with the
relevant test mode contact grounded (see above).
2. Press # to access test mode.
3. Press 18#, the phone will display "0 40000".
4. Enter the first inhibited system ID and press *.
Continue to enter additional system ID's if required. After the 5th entry
the phone will display "N2". Press * to continue and add system ID's for
NAM 2 as required.
5. If an incorrect entry is made (outside the range of 00000-32767) the
display will not advance, press CLR and re-enter. Use a setting of
40000 for any un-needed locations.
6. When the last entry has been made press * to store and press # to exit,
turn off power.
LOCK/UNLOCK PROCEDURES:
Phones with "LOCK" buttons: Press lock for at least 1/2 a second.
Phones with a "FCN" button: Press FCN 5, note that 5 has the letter's
"J,K, and L" for lock.
Phones with no FCN or LOCK button: Press Control 5, control is the black
volume button on the side of the
handset.
SYSTEM SELECT PROCEDURES:
Phones with a RCL button: Press RCL *, then * to select, STO to store.
Phones with no RCL button: Press Control * then * to select, # to store.
Options are: CSCAn: Preferred/Non preferred with system lockout.
Std A/b, or Std b/A: Preferred/Non preferred.
SCAn Ab, or SCAn bA: Non preferred/Preferred
SCAn A: "A" ONLY
SCAn b: "B" ONLY
HOME: Home only
(these are typical options, some phone's vary. C-Scan only available on
newer models and does not appear unless programed, see above.)
GENERAL NOTES:
HANDSETS: Most Motorola handsets are interchangeable, when a handset is
used with a transceiver other than the one it was designed for the display
will show "LOANER". Some features and buttons may not work, for instance
if the original handset did not have a RCL or STO button, and the
replacement does, you will have to use the control * or control # sequence
to access memory and A/B system select procedures.